JADODE For Chrysler 300 300C Dodge Magnum Charger Outside Door Handle Chrome 4 Piece
Free Shipping
FREE Standard Shipping | Located in: United States
Returns
30 days returns | Seller pays for return shipping
- Material:Plastic
- Type:Door Handle
- Placement on Vehicle: Left, Right, Front, Rear Side
- Primary Color: Chrome
- Surface Finish:Chrome
- Replaces OEM Part Number: 4589009AH , 4589009AD , 4589009AG , 5065800AE , 5065800AG , 5065801AE , 5065801AG
- Interchange Part Number: 5065801AG, 80609, CH-3300M-RL, 735-6710, 5065800AH,5065800AG,80607, 4589009AH,4589009AD,80608, 5065800AE, 5065800AG, 5065801AE
- Manufacturer Part Number: 4589009AH , 4589009AD , 4589009AG
Fitment
- 2005 - 2010 Chrysler 300 / 300C
- 2005 - 2008 Dodge Magnum
- 2007 Dodge Charger
- Pry out the trim piece inside the door handle
- Remove the Phillips screw behind the handle
- Remove the tan circle clips by pressing in the center and prying out the clip
- Remove the four Phillips head screws on the bottom of the panel
- Pry out the panel below the door pull
- Pry out the door panel with a door panel clip tool or putty knife
- Release the door handle cable by popping the clip, rotating the handle, and popping the hook out
- Disconnect the window switch wiring harnesses
- Pop out the wire harness retainers
- Unplug the courtesy light and its wire retainers
- Lift the door panel up and off
- Disconnect the connectors on the door control module
- Pry out the plastic clips on the module
- Pry off the wire harness retainers
- Pry off the adhesive on the weathershield
- Release the lock and latch rod clips
- Remove the two 8mm bolts from the door handle
- Remove the door lock cylinder
- Remove the door handle
- Insert the door handle into the door, starting with the front
- Tighten the 8mm screw to the door handle
- Insert the door lock cylinder into the handle
- Tighten the 8mm bolt to the cylinder
- Connect the lock and latch rod clips
- Connect the wire harness retainers
- Press the module into the door
- Connect the connectors to the module
- Connect the courtesy light
- Clip in the wire harness retainers
- Connect the window switch wiring harnesses
- Insert the latch rod into the door handle
- Slide the clip over the latch rod
- Lift the panel up over the door lock
- Press the panel into place
- Press the clips into the door panel
- Tighten the four Phillips screws to the bottom of the panel
- Tighten the Phillips screws beneath the door pull
- Tighten the Phillips screw into the door handle
- Press on the trim buttons
- Please allow 1-3mm differs due to manual measurement.
- Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding.
Shipping Policy
Item location:United States
Ships to: United States
If you have any questions, please contact our customer service folks. comi@autousa.com
RETURNS POLICY
After receiving the item, contact seller within 30 days, and seller pays for return shipping.
We do not accept returned products that have already been installed, please contact customer service for replacement or refunds All returns must include the following:
1.Original packaging (manufacturer's box, plastic bags, etc.)
2.Valid Return Merchandise Authorization (RMA)
3.All accessories (lubricant, stickers, installation instructions)
4.Manufacturer documentation (manuals, warranty cards, registration information, etc.)
5.The RMA number must not be written on the original manufacturer's packaging or box. Please write the RMA number on the label used to return the item or the return shipping box. Items received with any writing on the original manufacturer's packaging or box will be refused and returned to you at your cost and without credit approval.
